Basic Machinery Vibration (YOGYAKARTA)
TRAINING TIME :
- 28 Okt 2019-31 Okt 2019
- 04 Nop 2019-07 Nop 2019
- 16 Des 2019-19 Des 2019
VENUE : Yogyakarta (Jogjakarta plaza hotel/Ibis hotel yogyakarta/Ibis Styles yogyakarta hotel/Mutiara hotel/ Melia Purosani hotel)
TRAINING DURATION : 4 days
PENGANTAR:
Amplitudo getaran mesin yang berlebihan akan mempengaruhi kualitas serta umur mesin tersebut, oleh karena itu amplitudo getaran yang terjadi harus dibuat agar di bawah ambang batas standar yang ada. Untuk mengurangi amplitudo getaran, selain diperlukan sensor dan analyzer, juga diperlukan pengetahuan yang memadai. Tanpa pengetahuan yang memadai maka analisis tidak dapat dilakukan secara maksimal. Pengetahuan dasar yang diperlukan adalah meliputi: dinamika struktur, dinamika komponen rotasi serta metode analisis sinyal getaran. Kursus ini mengulas dasar-dasar pengetahuan yang diperlukan untuk analisis problem getaran, yang melipui: pengetahuan tentang dinamika struktur mesin rotasi maupun struktur penumpuny ( resonansi dan modus getar), tentang metode pengukuran getaran serta analisisnya, ciri-ciri kerusakan komponen rotasi, analisis sinyal, pengetahuan tentang sensor serta vibration analyzer, pengukuran getaran di atas 20 kHz (modulasi sinyal, SPM), serta pengantar untuk analisis dan problem solving.
TUJUAN TRAINING:
Setelah mengikuti training, peserta mengerti tentang prinsip dasar pengukuran vibrasi, pengetahuan tentang kondisi struktur penumpu mesin, setting peralatan vibrasi serta analisis atas sinyal vibrasi untuk problem solving.
SIAPA SEBAIKNYA MENGIKUTI TRAINING INI?:
operator maupun engineer yang berkecimpung di maintenance dan vibration monitoring dan analisis dan semua pihak yang ingin memahami topik ini.
CAKUPAN MATERI TRAINING:
1. Pengantar
- Mengapa getaran muncul ?
- Sejaran pengukuran getaran
- Mengapa getaran dapat dijadikan sebagai tolok ukur kerusakan?
2. Dasar-dasar
- Amplitudo, frekuensi dan sudut fasa
- Displacement, velocity dan acceleration
- Dinamika struktur
- Pengubahan pola dinamika struktur (penggeseran frekuensi resonansi)
- Peredaman getaran
3. Pengukuran sinyal getaran
- Sensor getaran dan prinsip kerjanya
- Daerah kerja sensor
- Kalibrasi sensor
- Set-up sistem pengukuran getaran
- Signal analyzer: FFT, Windowing, Coupling, Antialias filter, averaging, measurement unit, etc.
- Pengukuran getaran, setting parameter pengukuran.
- Jenis-jenis tampilan grafik: power spectrum, linear spectrum, waterfall diagram, polar plot
- Pengolahan sinyal getaran
4. Analisis sinyal getaran
- Membaca grafik hasil pengukuran getaran
- Konversi data
- Membuat trending overall dan komponen
- Mechanical signature analysis
Unbalance
Misalignment
Rolling element
Gear
Belt, dll
5. Pengukuran Getaran bantalan, di atas 20 kHz
- Fenomena kerusakan bantalan gelinding
- Keterbatasan sensor accelerometer
- Teknik Modulasi Sinyal, SPM
- Acoustic emission
INSTRUCTOR : Dr.Ir. Paryana Puspaputra, M.Eng., and Team
INVESTMENT PRICE/PERSON :
- Rp. 8.500.000/person (full fare) or
- Rp. 8.250.000/person (early bird, payment 1 week before training) or
- Rp. 7.950.000/person (if there are 3 persons or more from the same company)
FACILITIES FOR PARTICIPANTS:
- Training Module
- Flash Disk contains training material
- Certificate
- Stationeries: NoteBook and Ballpoint
- T-Shirt
- Backpack
- Training Photo
- Training room with Full AC facilities and multimedia
- Lunch and twice coffeebreak every day of training
- Qualified Instructor
- Transportation for participants from hotel of participants to/from hotel of training – VV (if minimal participants is 4 persons from the same company)
TRAINING INSTRUCTOR
Paryana Puspaputra was born in Kotabumi on January 19, 1964, is a Lecturer at the Department of Mechanical Engineering, Faculty of Industrial Technology, Indonesia Islamic University – Indonesia. Undergraduate from Department of Mechanical Engineering, Bandung Institute of Technology, Indonesia (ITB) in 1990 and master degree in Mechanical Engineering Department of Nagaoka University of Technology, Japan in 1996. He achieved his doctorate degree in Department of Mechanical Engineering, Bandung Institute of Technology, Indonesia (ITB) in 2012. He is also experienced as consultant and training instructure for several manufacturing and oil company, such as Chevron, Total, KPA, Petrokimia, Semen, Indonesia Power, etc. His background in mechanical equipment and machinery is completed with knowledge in instrumentation technology which was started from his final project in undergraduate by making software and data acquisition for predictive maintenance, and continued with his graduate thesis in control system for nano technology. There are researches and industrial implementation in data acquisition such as building the DNC system for production-shop using CNC machine, developing the balancing machine for Panasia Indosyntex – Bandung, SCADA system Development based on Fuji Electric control system (for IPAL – Pertamina – Cilacap, Toxic Gas Monitoring – Dieng – Central Java, etc). Moreover, he is also an official trainer of softwares for design and manufacturing base on CAD/CAM Technology (AutoCAD, Inventor, and Delcam PowerShape, ArtCAM) and familier with some finite element based analysys softwares such as Moldflow, ANSYS, SAP, CAESAR II, etc.
