Jadwal Training 2024

Power Management System

 

Power Management System

Tanggal
14 – 16 Juli 2014
26 – 28 Agustus 2014
22 – 24 September 2014
27 – 29 Oktober 2014
24 – 26 November 2014
29 – 31 Desember 2014

Training Duration
3 hari

Tempat
Yogyakarta (Jogjakarta plaza hotel/Ibis hotel yogyakarta/Ibis Styles yogyakarta hotel/Mutiara hotel/ Melia Purosani hotel)

Harga

  • Rp 5.950.000/peserta (bayar penuh)  atau
  • Rp 5.750.000/peserta (early bird, yang membayar 1 minggu sebelum training) atau
  • Rp 5.500.000/peserta (grup, untuk 3 peserta atau lebih dari 1 perusahaan yang sama)

TUJUAN
Setelah selesai mengikuti kursus ini, peserta diharapkan akan mengerti dan memahami masalah sistem tenaga listrik yang mampu menjamin kelancaran kegiatan produksi dengan handal, bermutu tinggi dan ekonomis, terutama pada managemen listrik pada sisi beban. Seperti bagaimana manajemen beban dapat menyediakan listrik yang cukup disaat dibutuhkan dan bagaimana peralatan dapat berjalan dengan tingkat konsumsi listrik yang minimum.

CAKUPAN MATERI TRAINING:

  • Organizing of Energy Management.
  • Translating Energy Into Cost.
  • Load Management.
  • Energy Management for Motor, System and Electrical Equipment.
  • Metering for Energy Management.
  • Energy Management for Lightning System.
  • Cogeneration.
  • Interactive discussion

SIAPA SEBAIKNYA MENGIKUTI TRAINING INI?
SLTA/D3 dengan pengalaman kerja 3 tahun sebagai Teknisi, Operator yang mengerjakan managemen kelistrikan dan atau mereka yang dalam tugasnya memerlukan dan terkait dengan materi kursus.
Semua pihak yang ingin memahami topik ini

FACILITIES FOR PARTICIPANTS :

  • Modul Training
  • Flashdisk Training berisi materi training
  • Sertifikat
  • ATK: NoteBook dan Ballpoint
  • T-Shirt
  • Ransel
  • Foto Training
  • Ruang Training dengan fasilitas Full AC dan multimedia
  • Makan siang dan 2 kali coffeebreak
  • Instruktur yang Qualified
  • Transportasi untuk peserta dari hotel penginapan ke hotel tempat training – PP (jika peserta minimal dari satu perusahaan ada 4 peserta)Trainer

Trainer
Tugino, ST , MT
He was graduated from electrical engineering Universitas Gadjah Mada,UGM Yogyakarta. He is lecturer at electrical engineering STTNAS Yogyakarta, for some subjects such as robotics, control engineering, Programmable Logic Controller(PLC), computer network, instrumentation and measurement, electric installation. And also as lecturer at mechanical engineering UJB Yogyakarta for subject electrical power engineering. Mr. Tugino,ST.,MT.  is active training instructor, he has been delivering industrial training class to many companies in Indonesia for some subjects such as: Electrical Safety, DCS Operation and Maintenance, Genset Operation and Maintenance, Logic Control for Industry, Fundamental of Electrical, Advanced Process Control, PLC  SIEMEN  S7, Basic Telecommunication PABX, Audit Energi Listrik, Electrical Instalation in Hazardus Area, Low and Medium Voltage Switchgear, Cable  Fault Location  for  Testing of  Underground Power Cable, Protection of Electrical Power System, Building Maintenance Management, Generator and Excitation Operation and Maintenance, Lighning Protection and Grounding System, Basic Instrumentation and Control, Power Distribution System Protection, PLC Programmable Logic Controller using Siemen, Electrical & Mechanical Safety, Work at Height Scaffolding Safety, SCADA (Supervisory Control and Data Accuisition), Motor Maintenance and control, Control Valve and Instrumentation, And many others. Many companies has been becoming as participants in his training class such as:  Chevron Indonesia Company, PT Indocemen Cirebon dan PT Pertamina Limau, PT OCI Melamin Kaltim, PT total E&P Kaltim, PT Kodeko Pertamina, Indocemen  Kalsel  dan  PT  Pupuk  Kujang,  PT Petrokimia Gresik,  CNOOC SES  Ltd, ,PT Chevron Geothermal Drajat, PT MAK Kalasan dan  PT Pertamina Prabumulih, PT Kaltim Industrial Estate, PT Star Energy Bandung , PT Pertamina (Kedeco) Gresik, PT Telkom Bandung, PT Margaria Group Yogya, PT Nusa Halmahera Mineral, PT Tambang Bukit Asam, PT Star Energy Bandung, Politeknik Aceh, PT KPI Kaltim, PT Medco Palembang, PT Pertamina Cirebon ,PT Timah Bangka, PT PJB Bali, Refinery Cilegon, PT Chevron Duri dan Drajat , PT PKT Kaltim,PT INALUM Medan, PT Petrokimia Gresik, PT PJB PLN Gresik, PT Chevron Drajat, PT Pertamina Jawa Timur ,PT Semen gresik &   PT YTL Jatim, PT  Sari Husada Yogyakarta,  PT Pupuk Kujang, Iros PTD Irak,PT Petrochina Jambi, PT PJB Gresik, PT Kaltim Prima Coal, PT Semen Hocim Cilacap, PT Badak LNG Kaltim , PT. YTL Paiton Jawatimur,PT  Star  Energy Bandung, Medco Sumatra, PT Sriboga Semarang,PT PLN UJB Cirata, PT Indonesia Power Semarang, PT Indonesia Power Grati, PT Indonesia Power Semarang, PT DSM Kaltim, PT. Pertamina Learning Center, PT. PUSRI Palembang, PT. VICO Indonesia Kaltim, PT Kaltim Pasific Amoniak , UDIKLAT/PUSDIKLAT PLN (Medan, Palembang, Jakarta, Semarang, Surabaya, Makasar),  PT  Chevron  salak  dan  PT   Indonesia   Power semarang,   PT. IPMOMI Paiton, PT Chevron Garut, PTP,  PT PetroChina Sorong, , PT PERTAMINA Aceh, PT Pertamina Cilacap,  PT PERTAMINA Dumai, PT AZET Surya Lestari, PT Panca Manunggal Semarang, PG Jatiroto Lumajang Jatim and others.

Bagikan:

KONTAK CEPAT

Tags

 

Pengelola website informasi seminar dan training. Jika perusahaan Anda membutuhan pelatihan dengan jumlah peserta terbatas, silahkan kontak ke kami. CV INFOSEMINAR 0851-0197-2488

Jaringan Instalasi Tenaga & Perlengkapannya (Yogyakarta)

 

Jaringan Instalasi Tenaga & Perlengkapannya (Yogyakarta)

Tanggal
11-13 Agustus 2014
8-10 September 2014
6-8 Oktober 2014
10-12 November 2014
8-10 Desember 2014

Jam Pelaksanaan
08:00-16:00 wib

Tempat
Hotel Ibis Style Yogyakarta
Hotel Horisson Ultima Riss Yogyakarta
Hotel Grand Zurry Yogyakarta
Hotel Jambuluwuk Yogyakarta
dan Hotel-hotel berbintang di Yogyakarta

Pembicara / Fasilitator
Tugino, ST, MT dan Team
(Akademisi alumnus UGM, Trainer, Konsultan dalam bidang Electrical Engineering, yang telah berpengalaman dalam menangani berbagai judul, program dan permasalahan dalam bidang electrical, baik pada perusahaan BUMN, swasta lokal, nasional maupun multinasional; menjadi Tim Assessor dan asosiasi profesi electrical, serta mempunyai jam terbang hingga luar negeri, seperti di Australia, Thailand, Taiwan, Malaysia dan Singapura).

Harga
Rp. 7.500.000,-
Tidak Termasuk Akomodasi dan Penginapan
Sudah termasuk Makan siang, Coffee Break 2x, Training Kits, Modul Pelatihan dan Sertifikat

Tujuan Pelatihan
Setelah mengikuti pelatihan diharapkan peserta memiliki pengetahuan dan ketrampilan terhadap aspek-aspek pemasangan, pemeliharaan dan pengujian jaringan sistem tenaga listrik. Pelatihan ditekankan pada tehnik pemasangan, pengoperasian dan pemeliharaan jaringan.

Materi Pelatihan

  1. Jenis-Jenis Jaringan/Gardu (Jenis jaringan/gardu, Fungsi jaringan/gardu)
  2. Komponen2 Jaringan/Gardu (Fuse, Circuit Breaker, Disconecting Switch)
  3. Pemilihan Komponen Jaringan (Fuse, Circuit Breaker, Disconecting Switch)
  4. Tipe-tipe Relay Proteksi (Over Current Relay, Ground Fault Relay)
  5. Pemilihan dan Setting Relay
  6. Macam-macam Penghantar dan Cara Pemasangan

Wajib diikuti oleh
Pelatihan ini diberikan pada para tehnisi, operator maupun supervisor yang bekerja dibidang ketenagalistrikan di industri untuk menangani masalah operasi, instalasi dan pemeliharaan jaringan sistem tenaga listrik.

Bagikan:

KONTAK CEPAT

Tags

Avatar photo

 

Jika ada kebutuhan Inhouse training atau kelas khusus silahkan hubungi 0851-0197-2488 / 0899-8121-246 Petrus Soeganda. Untuk mengundang Petrus Soeganda sebagai Pembicara Internet Marketing

Quality System Engineering

Petrus Soeganda

Quality System Engineering Tanggal 8 – 11 September 2014 21 – 24 Oktober 2014 2 – 5 Desember 2014 Training Duration 4 (empat) hari Tempat ... Baca Selengkapnya

Quality System Engineering

 

Quality System Engineering

Tanggal
8 – 11 September 2014
21 – 24 Oktober 2014
2 – 5 Desember 2014

Training Duration
4 (empat) hari

Tempat
Hotel Kagum Group Bandung (Golden Flower, Banana Inn, Grand Seriti, Carrcadin, Amaroossa, Grand Serela, Gino Feruci, Verona Palace, Malaka, Zodiac Taurus)

INVESTATION PRICE/PERSON :

  • Rp 7.950.000/person (full fare)  or
  • Rp 7.750.000/person (early bird, payment 1 week before training)  or
  • Rp 7.500.000/person (if there are 3 or more participants from the same company)

LATAR BELAKANG
Perdagangan bebas antar negara membawa dampak yaitu persaingan dalam kualitas produk, harga, ketepatan waktu dalam memenuhi pesanan dan dampak lingkungan yang positif selama proses produksi. Kebijakan utama dalam mempertahankan posisi bisnis Indonesia dalam kancah perdagangan global adalah dengan meningkatkan dan mengembangkan kualitas keahlian serta kemampuan sumber daya manusia yang mampu menghasilkan kualitas produk yang berstandarisasi internasional dengan mempertahankan karakteristik nasional.

Acuan standarisasi dalam pembentukan sistem produksi bagi industri rekayasa harus diterapkan secara nyata untuk menghasilkan produk yang berkualitas. Secara umum metoda pemanfaatan standar ini diulas dalam standar internasional yaitu ISO 9000 (Quality management and Quality Assurance Standards; Guidelines for Selection and Use): ISO 9001, Quality Systems; Model for Quality Assurance in Design/Development production, Installation and Servicing; ISO 9004, Quality Systems; Quality Management and Quality System Elements; Guidelines. Atau Standar Nasional Indonesia (SNI): SNI 19-9001 dan SNI 19-9004.

Untuk mendukung sistem produksi yang memadai diperlukan tenaga kerja yang handal atau peningkatan keahlian tenaga kerja profesi Teknologi Sistem Mutu (Quality System Engineering).

SIAPA SEBAIKNYA MENGIKUTI TRAINING INI ?
Para praktisi tingkat operator, tingkat penyelia atau perencana bidang teknologi sistem mutu pada industri rekayasa.

TUJUAN TRAINING
Setelah mengikuti pelatihan ini para peserta diharapkan memiliki pemahaman lebih tentang pengetahuan penanganan sistem mutu.

CAKUPAN MATERI TRAINING

  1. Konsep dasar penjaminan kualitas
    Pengertian penjaminan kualitas, tujuan penjaminan kualitas, hubungan pengendalian kualitas dengan penjaminan kualitas.
  2. Pemahaman total quality system
  3. ISO 9004, Quality management and quality system elements
  4. ISO 9001, Model for quality assurance in design/development, production, installation, and servicing
  5. Sistem penjaminan kualitas
    Prinsip dasar dan tujuan serta tugas sistem penjaminan kualitas, upaya dan strategi budaya kualitas, standar kualitas, model dan proses serta strategi penjaminan kualitas, peningkatan kualitas secara berkelanjutan.

FACILITIES FOR PARTICIPANTS :

  1. Modul Training
  2. Flashdisk Training berisi materi training
  3. Sertifikat
  4. ATK: NoteBook dan Ballpoint
  5. T-Shirt
  6. Ransel
  7. Foto Training
  8. Ruang Training dengan fasilitas Full AC dan multimedia
  9. Makan siang dan 2 kali coffeebreak
  10. Instruktur yang Qualified
  11. Transportasi untuk peserta dari hotel penginapan ke hotel tempat training – PP (jika peserta minimal dari satu perusahaan ada 4 peserta)

Trainer
SUGENG ISDWIYANUDI, Ir. MT. And Team
was graduated from politeknik universitas brawijaya malang for his diploma in mechanical engineering majoring on mechanical maintenance and repairing, from ITS Surabaya for his bachelor in mechanical engineering majoring on production engineering, and from ITB Bandung for his master program in mechanical engineering majoring on production engineering.

Now he is as lecturer at mechanical engineering Politeknik Negeri Bandung(before as poltek ITB). Ir. Sugeng Isdwiyanudi, MT. has followed many trainings/courses to improve his competence.

He is active instructor who often deliver training for industrial participants in Indonesia, many topics he teachs in training e.g.: pump and piping, Operation and Maintenance Boiler, Operator pressure vessel 1 (cooperated with Depnaker RI), Operation and Maintenance Centrifugal Pump, Effective Shutdown Maintenance, Reliability Centered Maintenance, Advanced Reliability Performance and Hidden Failure Supporting, Management Inventory Control, Alignment, Balancing, and Vibratio , Rotating Equipment: Operation and Maintenance, Material technique, Oil Analysis, Maintenance Management (Preventive and Predictive Maintenance),Heavy Equipment Maintenance, Basic Mechanical, Strength of Material, Electro Pneumatic and Hydraulic, Rotating Equipment Alignment and Vibration, Operation and Maintenance Diesel Engine, Operation and Maintenance Boiler, Operation and Maintenance Pump and Compressor, Pressure Vessel and Tank, Preventive and Predictive Maintenance, Total Productive Maintenance (TPM), Heavy Equipment Maintenance Management, Maintenance Equipment Management for Mining, Modern Maintenance and Spare Part Management System, NDT and Quality Assurance, Integrated Material Management, Effective Production Management, Plant Life Management through Reliability Based Inspection, Maintenance Planning, Scheduling, and Coordination, Integrated Maintenance Management and Control, Implementation RCM and RBI in Industries, Total Productive Maintenance (TPM), Reliability Centered Maintenance (RCM), Oerator Routine Daily Checklist and Driven Reliability, Measuring, Monitoring, and Analysis of Machinery Vibration, Vibration Prevention and Monitoring System, Advanced Application of CSI 2120/2130 and AMS Suite (RBM) for Condition Monitoring and Troubleshooting, Root Cause Failure Analysis (RCFA), NDT and Quality Assurance, Piping System. In campus he teachs for some subjects e.g.: industrial metrology, quality control, Instrumentation and measurement, machining technique, production system and quality control, Pneumatics and hydrolics, measurement system, measuremen technique(Metrology of Geometry), mechanics vibration, management of production process, product quality control, statistics application in mechanical engineering, machining process technology, Practice of industrial metrology, pneumatics control system.

In campus he has many experiences e.g.: as head of Laboratory industrial Metrology POLBAN, as head of Laboratory Metrology POLBAN, as director SPMU TPSDP POLBAN (ADB Loan 1792-INO), director asistant administration and finance SPMU TPSDP POLBAN (ADB Loan 1792-INO), head of production research group POLBAN, head of department mechanical engineering P4D, department secretary of mechanical department P4D, head of Laboratory Pneumatics and Hydrolics P4D. He invites industrial participants to share and discuss in his training class.

Bagikan:

KONTAK CEPAT

Tags

, , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,

 

Pengelola website informasi seminar dan training. Jika perusahaan Anda membutuhan pelatihan dengan jumlah peserta terbatas, silahkan kontak ke kami. CV INFOSEMINAR 0851-0197-2488

Advance Process Control, Intrumentation And Metering (BANDUNG)

 

Advance Process Control, Intrumentation And Metering (BANDUNG)

Tanggal
30 Juni – 3 Juli 2014
11 – 14 Agustus 2014
1 – 4 September 2014
29 September – 2 Oktober 2014
3 – 6 November 2014
1 – 4 Desember 2014

Jam Pelaksanaan
08.30-16.30 WIB

Tempat
Hotel Kagum Group Bandung (Golden Flower, Banana Inn, Grand Seriti, Carrcadin, Amaroossa, Grand Serela, Gino Feruci, Verona Palace, Malaka, Zodiac Taurus)

Pembicara / Fasilitator
Dr.Ir. Sutanto Hadisupadmo.MT.,IPM is a lecturer at Physics Engineering Bandung Institute of Technology (ITB), and has been as a Head of Laboratory of Industrial Instrumentation at ITB. He is former Director of Instrumentation Center and Technical Services of ITB. His education started at Engineering Physics, Bandung Institute of Technology (ITB-1977), then at Diplome Universite in Energetique, Universite de Prepignan, France (1985), Magister Engineering in Instrumentation and Control (ITB) and Doctor (ITB). He has over 20 years of experience doing training, consulting work in instrumentation, measurement, safety and process control and Mr. Sutanto has trained many training/courses for many companies in Indonesia such as PT. TOTAL Indonesie, Pertamina, PT. Petrokimia Gresik, PT. Badak LNG, PT. Pupuk Iskandar Muda, PT. Pupuk Kaltim, PT. Jaya Ancol and many others. As professional he has handled many projects in Instrumentation Process, Tools Evaluation, Transmitter, General Evaluation of Instrumentation Specification, Commercial Building Power Audit, Maintenance Management Evaluation, etc. To get more advance information and knowledge he has participated in domestic and overseas training, seminar, workshop and conference as participant or speakers.

INVESTATION PRICE/PERSON :

  • Rp 8.500.000/person (full fare)  or
  • Rp 8.250.000/person (early bird, payment 1 week before training) or
  • Rp 7.950.000/person (if there are 3 persons or more from the same company)

OBJECTIVE:
To understand the scope and utilization of instrumentation and Advanced process control technology applicable to industry.

THE MAJOR COURSE OUTLINE:

Introduction
* Review Process Control
* Control loops
* Noise, load, disturbances
* Control objectives

Advanced strategies
* Cascade
* Feed forward
* Override
* Selection
* Ratio control

Advanced Process Control
* Simple process method
* Types of processes
* Fuzzy Logic Control
* Artificial Neural Network for Control
* Model Predictive Control

Advanced Metering
* Application Advanced Process Control in Industries

FACILITIES FOR PARTICIPANTS:

  • Training Module
  • Flash Disk contains training material
  • Certificate
  • Stationeries: NoteBook and Ballpoint
  • T-Shirt
  • Backpack
  • Training Photo
  • Training room with full AC facilities and multimedia
  • Lunch and twice coffeebreak everyday of training
  • Qualified instructor
  • Transportation for participants from hotel of participants to/from hotel of training (if minimal number of participants from one company is 4 persons)

 

WHO SHOULD ATTEND?
Senior Technicians, Production Supervisors, Instrumentation Engineers & Technicians

 

Bagikan:

KONTAK CEPAT

Tags

Avatar photo

 

Jika ada kebutuhan Inhouse training atau kelas khusus silahkan hubungi 0851-0197-2488 / 0899-8121-246 Petrus Soeganda. Untuk mengundang Petrus Soeganda sebagai Pembicara Internet Marketing

Non Destructive Test (NDT)

Jadwal Training

Non Destructive Test (NDT) TRAINING TIME :   18 – 21 Agustus 2014 30 September – 3 Oktober 2014 17 – 20 November 2014 VENUE :   ... Baca Selengkapnya

Non Destructive Test (NDT)

 

Non Destructive Test (NDT)

TRAINING TIME :  
18 – 21 Agustus 2014
30 September – 3 Oktober 2014
17 – 20 November 2014

VENUE :   Hotel Kagum Group Bandung (Golden Flower, Banana Inn, Grand Seriti, Carrcadin, Amaroossa, Grand Serela, Gino Feruci, Verona Palace, Malaka, Zodiac Taurus)

TRAINING DURATION :   4 days

PENDAHULUAN :  
Non Destructive Test; NDT adalah pengujian material yang dilakukan tanpa harus merusak bagian konstruksi (produk, material) atau obyek yang diuji untuk mengetahui cacat baik cacat luar maupun cacat dalam. Pemeriksaan kualitas terhadap cacat produk (material) dilakukan setiap kali apabila diperlukan. Berkenaan dengan penilaian produk catat yang diteliti, penerimaan dan penolakannya dalam penggunaan dan nilai barang dalam rupa, dipakai sebagai patokan penilaian. Bagi produk yang penilaiannya sulit karena ada pada batas antara diterima dan ditolak, maka hal ini harus diyakinkan dengan pengujian benda palsu atau pengujian dalam penggunaannya. Pemeriksaan harus dilakukan sedemikian rupa sehingga dari pemeriksaan diperoleh keyakinan. Untuk mendukung sistem produksi yang memadai diperlukan tenaga kerja yang handal atau peningkatan keahlian tenaga kerja profesi Pengujian Material Bersifat Tidak merusak (Non Destuctive Test).

PESERTA TRAINING :  
Para praktisi tingkat operator, tingkat penyelia atau perencana bidang pengujian material bersifat tidak merusak pada industri rekayasa.

TUJUAN TRAINING :  
Setelah mengikuti pelatihan ini peserta diharapkan memiliki pemahaman lebih tentang pengetahuan dan keahlian dalam pengujian karakteristik material bersifat tidak merusak.

CAKUPAN MATERI TRAINING :
1.    Struktur logam dan diagram fasa
2.    Ultrasonic test
3.    Die penetrate test
4.    X-Ray test
5.    Eddy current test
6.    Magnetic particle
7.    Analisis hasil pengujian non destructive test

INSTRUCTOR :    Ir. Sugeng Isdwiyanudi, MT.   and Team

INVESTATION PRICE/PERSON :   

  • Rp 7.950.000/person (full fare)  or
  • Rp 7.750.000/person (early bird, payment 1 week before training)  or
  • Rp 7.500.000/person (if there are 3 or more participants from the same company)

FACILITIES FOR PARTICIPANTS:

  • Training Module
  • Flash Disk contains training material
  • Certificate
  • Stationeries: NoteBook and Ballpoint
  • T-Shirt
  • Backpack
  • Training Photo
  • Training room with full AC facilities and multimedia
  • Lunch and twice coffeebreak everyday of training
  • Qualified instructor
  • Transportation for participants from hotel of participants to/from hotel of training (if minimal number of participants from one company is 4 persons)

TRAINING INSTRUCTOR
SUGENG ISDWIYANUDI, Ir. MT. And Team
He was graduated from politeknik  universitas brawijaya malang for his diploma in mechanical engineering majoring on mechanical maintenance and repairing, from ITS Surabaya for his bachelor in mechanical engineering majoring on production engineering, and from ITB Bandung for his master program in mechanical engineering majoring on production engineering. Now he is as lecturer at mechanical engineering Politeknik Negeri Bandung(before as poltek ITB). Ir. Sugeng Isdwiyanudi, MT. has followed many trainings/courses to improve his competence. He is active instructor who often deliver training for industrial participants in Indonesia, many topics he teachs in training e.g.: pump and piping, Operation and Maintenance Boiler, Operator pressure vessel 1 (cooperated with Depnaker RI), Operation and Maintenance Centrifugal Pump, Effective Shutdown Maintenance, Reliability Centered Maintenance, Advanced Reliability Performance and Hidden Failure Supporting, Management Inventory Control, Alignment, Balancing, and Vibration, Rotating Equipment: Operation and Maintenance, Material technique, Oil Analysis, Maintenance Management (Preventive and Predictive Maintenance),Heavy Equipment Maintenance, Basic Mechanical, Strength of Material, Electro Pneumatic and Hydraulic, Rotating Equipment Alignment and Vibration, Operation and Maintenance Diesel Engine, Operation and Maintenance Boiler, Operation and Maintenance Pump and Compressor, Pressure Vessel and Tank, Preventive and Predictive Maintenance, Total Productive Maintenance (TPM), Heavy Equipment Maintenance Management, Maintenance Equipment Management for Mining, Modern Maintenance and Spare Part Management System, NDT and Quality Assurance, Integrated Material Management, Effective Production Management, Plant Life Management through Reliability Based Inspection, Maintenance Planning, Scheduling, and Coordination, Integrated Maintenance Management and Control, Implementation RCM and RBI in Industries, Total Productive Maintenance (TPM), Reliability Centered Maintenance (RCM), Operator Routine Daily Checklist and Driven Reliability, Measuring, Monitoring, and Analysis of Machinery Vibration, Vibration Prevention and Monitoring System, Advanced Application of CSI 2120/2130 and AMS Suite (RBM) for Condition Monitoring and Troubleshooting, Root Cause Failure Analysis (RCFA), NDT and Quality Assurance, Piping System.  In campus he teachs for some subjects e.g.: industrial metrology, quality control, Instrumentation and measurement, machining technique, production system and quality control, Pneumatics and hydrolics, measurement system, measuremen technique(Metrology of Geometry), mechanics vibration, management of production process, product quality control, statistics application in mechanical engineering, machining process technology, Practice of industrial metrology, pneumatics control system. In campus he has many experiences e.g.: as head of Laboratory industrial Metrology POLBAN, as head of Laboratory Metrology POLBAN, as director SPMU TPSDP POLBAN (ADB Loan 1792-INO), director assistant administration and finance SPMU TPSDP POLBAN (ADB Loan 1792-INO), head of production research group POLBAN, head of department mechanical engineering P4D, department secretary of mechanical department P4D, head of Laboratory Pneumatics and Hydrolics P4D. He invites industrial participants to share and discuss in his training class.

Bagikan:

KONTAK CEPAT

Tags

Avatar photo

 

Jika ada kebutuhan Inhouse training atau kelas khusus silahkan hubungi 0851-0197-2488 / 0899-8121-246 Petrus Soeganda. Untuk mengundang Petrus Soeganda sebagai Pembicara Internet Marketing

Optimization For Production System

 

Optimization For Production System

Tanggal
7 – 10 Juli 2014
15 – 18 September 2014
28 – 31 Oktober 2014
9 – 12 Desember 2014

Tempat
Hotel Kagum Group Bandung (Golden Flower, Banana Inn, Grand Seriti, Carrcadin, Amaroossa, Grand Serela, Gino Feruci, Verona Palace, Malaka, Zodiac Taurus)

TRAINING DURATION :   4 days

LATAR BELAKANG:
Perencanaan kondisi proses perlu ditunjang dengan data mengenai ongkos produksi, ongkos pahat, ongkos operasi, dan data pemesinan yang lengkap yang biasanya tidak diketahui oleh seorang operator mesin. Hal ini sesungguhnya memang merupakan tugas bagi seorang ahli teknik produksi yang menguasai teori, memiliki data, dan pengalaman yang memungkinkan dalam penentuan kondisi proses pemesinan sesuai dengan tujuan dengan sebaik mungkin atau optimum. Dalam optimisasi kondisi pemesinan diperlukan suatu algoritma yaitu langkah logik yang menggunakan suatu model matematik untuk menghitung harga paling baik atau optimum bagi variabel proses pemesinan dapat dipenuhi, yaitu Ongkos produksi yang paling rendah atau ekonomik, Kecepatan produksi yang paling tinggi atau produktif, dan Kecepatan penghasilan keuntungan yang paling tinggi atau menguntungkan. Untuk mendukung sistem produksi yang memadai diperlukan tenaga kerja yang handal atau peningkatan keahlian tenaga kerja profesi Optimisasi Sistem Produksi (Optimization for Production System).

PESERTA:
Para praktisi tingkat operator, tingkat penyelia atau perencana bidang sistem produksi pada industri rekayasa.

OUTPUT TRAINING:
Pemahaman tentang pengetahuan optimisasi sistem produksi.

CAKUPAN MATERI TRAINING:
1.    Konsep dasar optimisasi sistem produksi.
2.    Waktu produksi.
3.    Ongkos produksi.
4.    Kondisi pemotongan optimum.
•    Kondisi pemotongan ekonomik
•    Kondisi pemotongan produktif
•    Kondisi pemotongan menguntungakan
5.    Ongkos operasi
6.    Teknik penentuan menit kerja per unit produksi
7.    Penetapan ongkos operasi (Rp/menit), ongkos pahat, ongkos penyiapan produksi (pemrograman, jigs & fixtures, settings, dsb.)
8.    Analisis rinci proses pemesinan untuk mencapai kondisi optimum dengan memanfaatkan berbagai basis data pemesinan.
9.    Penerapan, pemantauan dan penyesuaian/modifikasi kondisi optimum proses.
10.    Pemakaian/pemanfaatan software perancangan proses pemesinan.

INVESTATION PRICE/PERSON :   

  • Rp 7.950.000/person (full fare)  or
  • Rp 7.750.000/person (early bird, payment 1 week before training)  or
  • Rp 7.500.000/person (if there are 3 or more participants from the same company)

FACILITIES FOR PARTICIPANTS:

  • Training Module
  • Flash Disk contains training material
  • Certificate
  • Stationeries: NoteBook and Ballpoint
  • T-Shirt
  • Backpack
  • Training Photo
  • Training room with full AC facilities and multimedia
  • Lunch and twice coffeebreak everyday of training
  • Qualified instructor
  • Transportation for participants from hotel of participants to/from hotel of training (if minimal number of participants from one company is 4 persons)

TRAINING INSTRUCTOR
SUGENG ISDWIYANUDI, Ir. MT. And Team
He was graduated from politeknik  universitas brawijaya malang for his diploma in mechanical engineering majoring on mechanical maintenance and repairing, from ITS Surabaya for his bachelor in mechanical engineering majoring on production engineering, and from ITB Bandung for his master program in mechanical engineering majoring on production engineering. Now he is as lecturer at mechanical engineering Politeknik Negeri Bandung(before as poltek ITB). Ir. Sugeng Isdwiyanudi, MT. has followed many trainings/courses to improve his competence. He is active instructor who often deliver training for industrial participants in Indonesia, many topics he teachs in training e.g.:

Pump and piping, Operation and Maintenance Boiler, Operator pressure vessel 1 (cooperated with Depnaker RI), Operation and Maintenance Centrifugal Pump, Effective Shutdown Maintenance, Reliability Centered Maintenance, Advanced Reliability Performance and Hidden Failure Supporting, Management Inventory Control, Alignment, Balancing, and Vibration, Rotating Equipment: Operation and Maintenance, Material technique, Oil Analysis, Maintenance Management (Preventive and Predictive Maintenance),Heavy Equipment Maintenance, Basic Mechanical, Strength of Material, Electro Pneumatic and Hydraulic, Rotating Equipment Alignment and Vibration, Operation and Maintenance Diesel Engine, Operation and Maintenance Boiler, Operation and Maintenance Pump and Compressor, Pressure Vessel and Tank, Preventive and Predictive Maintenance, Total Productive Maintenance (TPM), Heavy Equipment Maintenance Management, Maintenance Equipment Management for Mining, Modern Maintenance and Spare Part Management System, NDT and Quality Assurance, Integrated Material Management, Effective Production Management, Plant Life Management through Reliability Based Inspection, Maintenance Planning, Scheduling, and Coordination, Integrated Maintenance Management and Control, Implementation RCM and RBI in Industries, Total Productive Maintenance (TPM), Reliability Centered Maintenance (RCM), Operator Routine Daily Checklist and Driven Reliability, Measuring, Monitoring, and Analysis of Machinery Vibration, Vibration Prevention and Monitoring System, Advanced Application of CSI 2120/2130 and AMS Suite (RBM) for Condition Monitoring and Troubleshooting, Root Cause Failure Analysis (RCFA), NDT and Quality Assurance, Piping System.

In campus he teachs for some subjects e.g.: industrial metrology, quality control, Instrumentation and measurement, machining technique, production system and quality control, Pneumatics and hydrolics, measurement system, measuremen technique(Metrology of Geometry), mechanics vibration, management of production process, product quality control, statistics application in mechanical engineering, machining process technology, Practice of industrial metrology, pneumatics control system. In campus he has many experiences e.g.: as head of Laboratory industrial Metrology POLBAN, as head of Laboratory Metrology POLBAN, as director SPMU TPSDP POLBAN (ADB Loan 1792-INO), director assistant administration and finance SPMU TPSDP POLBAN (ADB Loan 1792-INO), head of production research group POLBAN, head of department mechanical engineering P4D, department secretary of mechanical department P4D, head of Laboratory Pneumatics and Hydrolics P4D. He invites industrial participants to share and discuss in his training class.

Bagikan:

KONTAK CEPAT

Tags

Avatar photo

 

Jika ada kebutuhan Inhouse training atau kelas khusus silahkan hubungi 0851-0197-2488 / 0899-8121-246 Petrus Soeganda. Untuk mengundang Petrus Soeganda sebagai Pembicara Internet Marketing

Maintenance Management (For Manufacture Oil And Gas Company)

 

Maintenance Management (For Manufacture Oil And Gas Company)

Tanggal
14 – 16 Juli 2014
26 – 28 Agustus 2014
17 – 19 September 2014
20 – 22 Oktober 2014
19 – 21 November 2014
17 – 19 Desember 2014

Tempat
Hotel Kagum Group Bandung (Golden Flower, Banana Inn, Grand Seriti, Carrcadin, Amaroossa, Grand Serela, Gino Feruci, Verona Palace, Malaka, Zodiac Taurus)

TRAINING DURATION :   3 hari

INTRODUCTION :  
Kegiatan maintenance memegang peranan yang sangat penting dalam menjaga performansi alat-alat (mesin) dan perlengkapan lainnya didalam suatu perusahaan. Selain itu juga dalam rangka melakukan efisiensi investasi alat dan perlengkapan lainnya, kegiatan maintenance sangatlah diperlukan. Hal lain yang tidak kalah pentingnya adalah dengan memiliki perencanaan kegiatan maintenance yang baik, maka pihak perusahaan dapat memprediksi kapan akan terjadi penurunan performansi yang berdampak pada kegiatan produksinya atau juga dengan perencanaan maintenance yang baik pihak perusahaan dapat merencanakan anggaran untuk pembelian alat dan perlengkapan baru lainnya. Oleh karena itu untuk tetap menjaga tingkat kepercayaan konsumen, maka pihak perusahaan sudah saatnya untuk memiliki perencanaan dan aktivitas yang berkelanjutan dalam hal maintenance ini.

CAKUPAN MATERI TRAINING :
1.    Basic Maintenance
2.    Maintenance Supporting
3.    Umur Ekonomis Mesin
4.    Maintenance Scheduling
5.    Maintenance Programs
6.    Role of Planner Maintenance
7.    Measuring Performance
8.    Documentation of Maintenance
9.    Software for Maintenance

REKOMENDASI :
Setiap peserta direkomendasikan untuk membawa laptop.

METODE TRAINING :
•    60% Teori
•    40% Praktik (Studi Kasus & Software)

INVESTATION PRICE/PERSON :   
1.    Rp 5.500.000/peserta (bayar penuh)  atau
2.    Rp 5.250.000/peserta (early bird, yang membayar 1 minggu sebelum training) atau
3.    Rp 4.950.000/peserta (grup, untuk 3 peserta atau lebih dari 1 perusahaan yang sama)

FACILITIES FOR PARTICIPANTS:
1.    Modul Training
2.    Flashdisk Training berisi materi training
3.    Sertifikat
4.    ATK: NoteBook dan Ballpoint
5.    T-Shirt
6.    Ransel
7.    Foto Training
8.    Ruang Training dengan fasilitas Full AC dan multimedia
9.    Makan siang dan 2 kali coffeebreak
10.    Instruktur yang Qualified
11.    Transportasi untuk peserta dari hotel penginapan ke hotel tempat training – PP (jika peserta minimal dari satu perusahaan ada 4 peserta)

TRAINING INSTRUCTOR
OKTRI MOHAMMAD FIRDAUS, ST., MT. Adalah  master lulusan Teknik dan Management Industri ITB, kini sebagai Dosen dan Sekretaris Program Studi Teknik Industri  Fakultas Teknik  Universitas Widyatama, Bandung. Jabatan lain sebagai Kepala Divisi Riset Logistic and Supply Center Universitas Widyatama Bandung, serta menjadi dosen untuk beberapa perguruan tinggi di Jawa Barat. Beberapa keahlian beliau dalam hal-hal sebagai berikut : SAP – Fundamentals, Analisis Pengukuran Kerja, komputerisasi pergudangan, Perancangan Sistem Kerja & Ergonomi, Supply Chain Management, Project management, Manajemen Perawatan & Operasional, Perencanaan dan Perancangan Produk, Strategi Operasi & Integrasi, Pemodelan Sistem dll. Selain pemakalah dalam seminar internasional dan nasional Knowledge Management Based On Expert System, Proceeding Asia Pasific Industrial Engineering and Management, beliau juga kerap menjadi instruktur pelatihan untuk perusahaan-perusahaan besar seperti : Chevron Pacific Indonesia, Freeport, Sandvik, Exxon Mobil, Pertamina, PT. Kaltim Prima Coal (KPC), Adaro, Toyota Motor Manufacturing Indonesia, Bank CIMB Niaga, PT. Pupuk Sriwijaya, Dinas Kesehatan Kabupaten Bandung, Direktorat Metrologi, PT. Telkom , Pikiran Rakyat, KIE Bontang, dan lain-lain.

Bagikan:

KONTAK CEPAT

Tags

Avatar photo

 

Jika ada kebutuhan Inhouse training atau kelas khusus silahkan hubungi 0851-0197-2488 / 0899-8121-246 Petrus Soeganda. Untuk mengundang Petrus Soeganda sebagai Pembicara Internet Marketing

Distributed Control System (DCS): Principles And Application

 

Distributed Control System (DCS): Principles And Application

TRAINING TIME :  
1 – 4 Juli 2014
18 – 21 Agustus 2014
8 – 11 September 2014
7 – 10 Oktober 2014
10 – 13 November 2014
8 – 11 Desember 2014

VENUE :   Yogyakarta (Jogjakarta plaza hotel/Ibis hotel yogyakarta/Ibis Styles yogyakarta hotel/Mutiara hotel/ Melia Purosani hotel)

TRAINING DURATION :  4 hari

TUJUAN :
Peserta diharapkan dapat memperoleh pengetahuan yang menyeluruh mengenai konsep dan aplikasi dari DCS dalam aplikasinya secara real di lapangan.

CAKUPAN MATERI TRAINING:

  • Introduction to distributed computing, overview of SCADA system.
  • Components, architectures, operation of DCS and its hardware (field devices, remote terminal units)
  • Controller structures.
  • Sequential control and batch control.
  • Control strategy and configuration.
  • Alarms & trending, programmable logic controllers.
  • Data communications and communications network.
  • Device level communication protocol.
  • Design of MMI.
  • System security and implementation.
  • Practice and interactive discussion

SIAPA SEBAIKNYA MENGIKUTI TRAINING INI?:

  • D3 atau SLTA yang berpengalaman kerja minimal 3 tahun, dan atau setara.
  • Teknisi, Operator dan Supervisor didalam bidang  instrumentasi, disain, control dan automation technology, dll di berbagai macam industri.
  • Mereka yang dalam tugasnya berhubungan dan atau terkait dengan materi kursus.
  • Seluruh pihak yang ingin memahami topik ini

INSTRUCTOR :  Tugino, ST.,MT. dan Tim

INVESTATION PRICE/PERSON :    

  • Rp 8.500.000/person (full fare)  or
  • Rp 8.250.000/person (early bird, payment 1 week before training)  or
  • Rp 7.950.000/person (if there are 3 or more participants from the same company)

FACILITIES FOR PARTICIPANTS :

  • Modul Training
  • Flashdisk Training berisi materi training
  • Sertifikat
  • ATK: NoteBook dan Ballpoint
  • T-Shirt
  • Ransel
  • Foto Training
  • Ruang Training dengan fasilitas Full AC dan multimedia
  • Makan siang dan 2 kali coffeebreak
  • Instruktur yang Qualified
  • Transportasi untuk peserta dari hotel penginapan ke hotel tempat training – PP (jika peserta minimal dari satu perusahaan ada 4 peserta)

INSTRUKTUR TRAINING
Tugino,ST.,MT. was graduated from electrical engineering Universitas Gadjah Mada,UGM Yogyakarta. He is lecturer at electrical engineering STTNAS Yogyakarta, for some subjects such as robotics, control engineering, Programmable Logic Controller(PLC), computer network, instrumentation and measurement, electric installation. And also as lecturer at mechanical engineering UJB Yogyakarta for subject electrical power engineering. Mr. Tugino,ST.,MT.  is active training instructor, he has been delivering industrial training class to many companies in Indonesia for some subjects such as: Electrical Safety, DCS Operation and Maintenance, Genset Operation and Maintenance, Logic Control for Industry, Fundamental of Electrical, Advanced Process Control, PLC  SIEMEN  S7, Basic Telecommunication PABX, Audit Energi Listrik, Electrical Instalation in Hazardus Area, Low and Medium Voltage Switchgear, Cable  Fault Location  for  Testing of  Underground Power Cable, Protection of Electrical Power System, Building Maintenance Management, Generator and Excitation Operation and Maintenance, Lighning Protection and Grounding System, Basic Instrumentation and Control, Power Distribution System Protection, PLC Programmable Logic Controller using Siemen, Electrical & Mechanical Safety, Work at Height Scaffolding Safety, SCADA (Supervisory Control and Data Accuisition), Motor Maintenance and control, Control Valve and Instrumentation, And many others. Many companies has been becoming as participants in his training class such as:  Chevron Indonesia Company, PT Indocemen Cirebon dan PT Pertamina Limau, PT OCI Melamin Kaltim, PT total E&P Kaltim, PT Kodeko Pertamina, Indocemen  Kalsel  dan  PT  Pupuk  Kujang,  PT Petrokimia Gresik,  CNOOC SES  Ltd, ,PT Chevron Geothermal Drajat, PT MAK Kalasan dan  PT Pertamina Prabumulih, PT Kaltim Industrial Estate, PT Star Energy Bandung , PT Pertamina (Kedeco) Gresik, PT Telkom Bandung, PT Margaria Group Yogya, PT Nusa Halmahera Mineral, PT Tambang Bukit Asam, PT Star Energy Bandung, Politeknik Aceh, PT KPI Kaltim, PT Medco Palembang, PT Pertamina Cirebon ,PT Timah Bangka, PT PJB Bali, Refinery Cilegon, PT Chevron Duri dan Drajat , PT PKT Kaltim,PT INALUM Medan, PT Petrokimia Gresik, PT PJB PLN Gresik, PT Chevron Drajat, PT Pertamina Jawa Timur ,PT Semen gresik &   PT YTL Jatim, PT  Sari Husada Yogyakarta,  PT Pupuk Kujang, Iros PTD Irak,PT Petrochina Jambi, PT PJB Gresik, PT Kaltim Prima Coal, PT Semen Hocim Cilacap, PT Badak LNG Kaltim , PT. YTL Paiton Jawatimur,PT  Star  Energy Bandung, Medco Sumatra, PT Sriboga Semarang,PT PLN UJB Cirata, PT Indonesia Power Semarang, PT Indonesia Power Grati, PT Indonesia Power Semarang, PT DSM Kaltim, PT. Pertamina Learning Center, PT. PUSRI Palembang, PT. VICO Indonesia Kaltim, PT Kaltim Pasific Amoniak , UDIKLAT/PUSDIKLAT PLN (Medan, Palembang, Jakarta, Semarang, Surabaya, Makasar),  PT  Chevron  salak  dan  PT   Indonesia   Power semarang,   PT. IPMOMI Paiton, PT Chevron Garut, PTP,  PT PetroChina Sorong, , PT PERTAMINA Aceh, PT Pertamina Cilacap,  PT PERTAMINA Dumai, PT AZET Surya Lestari, PT Panca Manunggal Semarang, PG Jatiroto Lumajang Jatim and others.

Bagikan:

KONTAK CEPAT

Tags

Avatar photo

 

Jika ada kebutuhan Inhouse training atau kelas khusus silahkan hubungi 0851-0197-2488 / 0899-8121-246 Petrus Soeganda. Untuk mengundang Petrus Soeganda sebagai Pembicara Internet Marketing

Welding Inspection & Quality Control (Yogyakarta)

 

Welding Inspection & Quality Control (Yogyakarta)

Tanggal    
16-18 Juni 2014
14-16 Juli 2014
18-20 Agustus 2014
15-17 September 2014
13-15 Oktober 2014
17-19 November 2014
15-17 Desember 2014

Jam Pelaksanaan    
08:00-16:00 wib

Tempat 
Hotel Ibis Style Yogyakarta
Hotel Horisson Ultima Riss Yogyakarta
Hotel Grand Zurry Yogyakarta
Hotel Jambuluwuk Yogyakarta
dan Hotel-hotel berbintang di Yogyakarta

Pembicara / Fasilitator    
Tugino, ST, MT dan Team
(Akademisi alumnus UGM, Trainer, Konsultan dalam bidang Electrical Engineering, yang telah berpengalaman dalam menangani berbagai judul, program dan permasalahan dalam bidang electrical, baik pada perusahaan BUMN, swasta lokal, nasional maupun multinasional; menjadi Tim Assessor dan asosiasi profesi electrical, serta mempunyai jam terbang hingga luar negeri, seperti di Australia, Thailand, Taiwan, Malaysia dan Singapura).

Harga     
Rp. 7.500.000,-
Tidak Termasuk Akomodasi dan Penginapan
Sudah termasuk Makan siang, Coffee Break 2x, Training Kits, Modul Pelatihan dan Sertifikat

Tujuan Pelatihan
Meningkatkan dan menambah wawasan bagi para personnel yang berkecimpung di dunia pengelasan, terutama mengenai teknologi dan klasifikasi proses pengelasan, pengetahuan bahan teknik, prosedur dan kualifikasi unjuk kerja juru las dan wawasan tentang Standard pengelasan yang berlaku.

Sasaran Pelatihan
Setelah mengikuti pendidikan dan pelatihan ini peserta diharapkan mampu :

  • Memahami prosedur kualifikasi juru las sesuai dengan standard
  • Memahami jenis – jenis proses pengelasan secara luas
  • Memahami teknologi pengelasan logam
  • Memahami macam – macam standard pengelasan
  • Metallurgy Las
  • Studi kasus

Materi :

  1. Inspeksi las (welding inspection)
  2. Pengenalan standar las
  3. Gambar teknik
  4. Non Destructive Testing (NDT)
  5. Pengujian sifat mekanis
  6. Kualifikasi prosedur las
  7. Welding design
  8. Pengetahuan bahan logam
  9. Metallurgy las
  10. Teknologi las
  11. Teknik pelaporan (dokumentasi)

Wajib diikuti oleh    
Pengawas teknik dan karyawan yang bertanggungjawab terhadap kualitas hasil pengelasan

 

Bagikan:

KONTAK CEPAT

Tags

Avatar photo

 

Jika ada kebutuhan Inhouse training atau kelas khusus silahkan hubungi 0851-0197-2488 / 0899-8121-246 Petrus Soeganda. Untuk mengundang Petrus Soeganda sebagai Pembicara Internet Marketing

Programmable Logic Controller (PLC) : Principles, Hardware and Software, Diagnostic And Troubleshooting

 

Programmable Logic Controller (PLC) : Principles, Hardware and Software, Diagnostic And Troubleshooting

Tanggal
20 – 23 Mei 2014
24 – 27 Juni 2014
15 – 18 Juli 2014
26 – 29 Agustus 2014
23 – 26 September 2014
27 – 30 Oktober 2014
25 – 28 November 2014
16 – 19 Desember 2014

Pukul
09.00-16.00 WIB

Tempat
Yogyakarta (Jogjakarta plaza hotel/Ibis hotel yogyakarta/Ibis Styles yogyakarta hotel/Mutiara hotel/ Melia Purosani hotel)

Investasi

  • Rp 7.250.000/person (full fare) atau
  • Rp 6.950.000/person (early bird, yang membayar 1 minggu sebelum training) atau
  • Rp 6.750.000/person (peserta bergroup 3 orang atau lebih dari 1 perusahaan yang sama)

Fasilitas Yang didapat

  • Modul Training
  • Flashdisk Training berisi materi training
  • Sertifikat
  • ATK: NoteBook dan Ballpoint
  • T-Shirt
  • Ransel
  • Foto Training
  • Ruang Training dengan fasilitas Full AC dan multimedia
  • Makan siang dan 2 kali coffeebreak
  • Instruktur yang Qualified
  • Transportasi untuk peserta dari hotel penginapan ke hotel tempat training – PP (jika peserta minimal dari satu perusahaan ada 4 peserta)

Instruktur
Tugino,ST.,MT. was graduated from electrical engineering Universitas Gadjah Mada,UGM Yogyakarta. He is lecturer at electrical engineering STTNAS Yogyakarta, for some subjects such as robotics, control engineering, Programmable Logic Controller(PLC), computer network, instrumentation and measurement, electric installation. And also as lecturer at mechanical engineering UJB Yogyakarta for subject electrical power engineering. Mr. Tugino,ST.,MT. is active training instructor, he has been delivering industrial training class to many companies in Indonesia for some subjects such as: Electrical Safety, DCS Operation and Maintenance, Genset Operation and Maintenance, Logic Control for Industry, Fundamental of Electrical, Advanced Process Control, PLC SIEMEN S7, Basic Telecommunication PABX, Audit Energi Listrik, Electrical Instalation in Hazardus Area, Low and Medium Voltage Switchgear, Cable Fault Location for Testing of Underground Power Cable, Protection of Electrical Power System, Building Maintenance Management, Generator and Excitation Operation and Maintenance, Lighning Protection and Grounding System, Basic Instrumentation and Control, Power Distribution System Protection, PLC Programmable Logic Controller using Siemen, Electrical & Mechanical Safety, Work at Height Scaffolding Safety, SCADA (Supervisory Control and Data Accuisition), Motor Maintenance and control, Control Valve and Instrumentation, And many others. Many companies has been becoming as participants in his training class such as: Chevron Indonesia Company, PT Indocemen Cirebon dan PT Pertamina Limau, PT OCI Melamin Kaltim, PT total E&P Kaltim, PT Kodeko Pertamina, Indocemen Kalsel dan PT Pupuk Kujang, PT Petrokimia Gresik, CNOOC SES Ltd, ,PT Chevron Geothermal Drajat, PT MAK Kalasan dan PT Pertamina Prabumulih, PT Kaltim Industrial Estate, PT Star Energy Bandung , PT Pertamina (Kedeco) Gresik, PT Telkom Bandung, PT Margaria Group Yogya, PT Nusa Halmahera Mineral, PT Tambang Bukit Asam, PT Star Energy Bandung, Politeknik Aceh, PT KPI Kaltim, PT Medco Palembang, PT Pertamina Cirebon ,PT Timah Bangka, PT PJB Bali, Refinery Cilegon, PT Chevron Duri dan Drajat , PT PKT Kaltim,PT INALUM Medan, PT Petrokimia Gresik, PT PJB PLN Gresik, PT Chevron Drajat, PT Pertamina Jawa Timur ,PT Semen gresik & PT YTL Jatim, PT Sari Husada Yogyakarta, PT Pupuk Kujang, Iros PTD Irak,PT Petrochina Jambi, PT PJB Gresik, PT Kaltim Prima Coal, PT Semen Hocim Cilacap, PT Badak LNG Kaltim , PT. YTL Paiton Jawatimur,PT Star Energy Bandung, Medco Sumatra, PT Sriboga Semarang,PT PLN UJB Cirata, PT Indonesia Power Semarang, PT Indonesia Power Grati, PT Indonesia Power Semarang, PT DSM Kaltim, PT. Pertamina Learning Center, PT. PUSRI Palembang, PT. VICO Indonesia Kaltim, PT Kaltim Pasific Amoniak , UDIKLAT/PUSDIKLAT PLN (Medan, Palembang, Jakarta, Semarang, Surabaya, Makasar), PT Chevron salak dan PT Indonesia Power semarang, PT. IPMOMI Paiton, PT Chevron Garut, PTP, PT PetroChina Sorong, , PT PERTAMINA Aceh, PT Pertamina Cilacap, PT PERTAMINA Dumai, PT AZET Surya Lestari, PT Panca Manunggal Semarang, PG Jatiroto Lumajang Jatim and others.

Tujuan Pelatihan
Kursus ini memberikan pemahaman terhadap PLC, kuncinya pada pengertian dasar PLC : Pemrograman AND / OR, batch programming techniques, PLC program scan cycle, program documentation, hardware considerations, diagnostic, troubleshooting dll.

Materi Training

  1. Brief history of PLC’s.
  2. Relay vs PLC’s.
  3. PLC function and possibilities.
  4. PLC I/O addressing.
  5. AND/OR programming.
  6. Examination ON and Examine OFF statesments.
  7. Sealing bits / latch programming.
  8. Program scan cycle.
  9. Ladder logic programming.
  10. Batch programming.
  11. Common problems bugs.
  12. Safety considerations.
  13. Programming counters.
  14. Programming timers.
  15. Numerical operations.
  16. Comparison statements.
  17. Latch / Unlatch statements.
  18. Advanced programming statements.
  19. Hardware modules & accessories.
  20. PLC installation & hookups.
  21. Diagnostics and troubleshooting.
  22. Emerging trends and capabilities.

Wajib diikuti oleh

  • D3 Elektro atau SLTA yang berpengalaman kerja minimal 3 tahun, dan atau setara.
  • Teknisi, Operator dan Supervisor yang memiliki basic computer skills dan familiar dengan basic electrical concept.
  • Mereka yang dalam tugasnya berhubungan dan atau terkait dengan materi kursus.
  • Semua pihak yang ingin memahami topik ini

 

Bagikan:

KONTAK CEPAT

Tags

Avatar photo

 

Jika ada kebutuhan Inhouse training atau kelas khusus silahkan hubungi 0851-0197-2488 / 0899-8121-246 Petrus Soeganda. Untuk mengundang Petrus Soeganda sebagai Pembicara Internet Marketing

Teknik Listrik Tegangan Rendah & Tinggi Dan Elektro Instrument

 

Teknik Listrik Tegangan Rendah & Tinggi Dan Elektro Instrument

Teknik Listrik Tegangan Rendah & Tinggi dan Elektroinstrument

TRAINING TIME :  
10 – 13 Juni 2014
7 – 10 Juli 2014
19 – 22 Agustus 2014
9 – 12 September 2014
13 – 16 Oktober 2014
11 – 14 November 2014
9 – 12 Desember 2014

VENUE :   Yogyakarta (Jogjakarta plaza hotel/Ibis hotel yogyakarta/Ibis Styles yogyakarta hotel/Mutiara hotel/ Melia Purosani hotel)

TRAINING DURATION :  4 hari

TUJUAN :
Peserta akan mendapatkan teori dasar dan aplikasi tentang listrik dan elektro instrument yang dibutuhkan sebagai pengetahuan dasar yang wajib dimiliki peserta.

CAKUPAN MATERI TRAINING:

  1. Dasar perhitungan listrik dan pengetahuan bahan listrik.
  2. Generator, transformer, motor listrik, dan distribusi AC dan DC.
  3. Proteksi saklar, fuse, relay, circuit breaker, ligthning arrestor.
  4. Membaca gambar listrik.
  5. Pengantar elektronika.
  6. Elektronika dasar.
  7. Elektronika digital.
  8. Dasar – dasar instrumentasi :
    Mekanik, pneumatik, elektrik.
  9. Instrumentation & valves :
    Measuring and controling.
  10. Instrumentation & valves :
    Scaling, control valves & setting.
  11. Aplikasi Pneumatik.
  12. Pengenalan umum Microprocessor.
  13. Peripheral Microprocessor, smart transmiitter.
  14. Case study, pemeliharaan dan troubleshooting.

SIAPA SEBAIKNYA MENGIKUTI TRAINING INI?:

  • D3 atau SLTA yang berpengalaman kerja minimal 3 tahun, dan atau setara.
  • Teknisi, Operator dan Supervisor non listrik atau karyawan yang membutuhkan pengetahuan dasar didalam bidang  kelistrikan, khususnya pada bidang teknik instrumentasi peralatan elektro instrument.
  • Mereka yang dalam tugasnya berhubungan dan atau terkait dengan materi kursus.
  • Semua pihak yang ingin memahami topik ini

INSTRUCTOR :  Tugino, ST.,MT. dan Tim

INVESTATION PRICE/PERSON :    

  • Rp 7.950.000/person (full fare)  or
  • Rp 7.750.000/person (early bird, payment 1 week before training)  or
  • Rp 7.500.000/person (if there are 3 or more participants from the same company)

FACILITIES FOR PARTICIPANTS :

  • Modul Training
  • Flashdisk Training berisi materi training
  • Sertifikat
  • ATK: NoteBook dan Ballpoint
  • T-Shirt
  • Ransel
  • Foto Training
  • Ruang Training dengan fasilitas Full AC dan multimedia
  • Makan siang dan 2 kali coffeebreak
  • Instruktur yang Qualified
  • Transportasi untuk peserta dari hotel penginapan ke hotel tempat training – PP (jika peserta minimal dari satu perusahaan ada 4 peserta)

INSTRUKTUR TRAINING
Tugino,ST.,MT. was graduated from electrical engineering Universitas Gadjah Mada,UGM Yogyakarta. He is lecturer at electrical engineering STTNAS Yogyakarta, for some subjects such as robotics, control engineering, Programmable Logic Controller(PLC), computer network, instrumentation and measurement, electric installation. And also as lecturer at mechanical engineering UJB Yogyakarta for subject electrical power engineering. Mr. Tugino,ST.,MT.  is active training instructor, he has been delivering industrial training class to many companies in Indonesia for some subjects such as: Electrical Safety, DCS Operation and Maintenance, Genset Operation and Maintenance, Logic Control for Industry, Fundamental of Electrical, Advanced Process Control, PLC  SIEMEN  S7, Basic Telecommunication PABX, Audit Energi Listrik, Electrical Instalation in Hazardus Area, Low and Medium Voltage Switchgear, Cable  Fault Location  for  Testing of  Underground Power Cable, Protection of Electrical Power System, Building Maintenance Management, Generator and Excitation Operation and Maintenance, Lighning Protection and Grounding System, Basic Instrumentation and Control, Power Distribution System Protection, PLC Programmable Logic Controller using Siemen, Electrical & Mechanical Safety, Work at Height Scaffolding Safety, SCADA (Supervisory Control and Data Accuisition), Motor Maintenance and control, Control Valve and Instrumentation, And many others. Many companies has been becoming as participants in his training class such as:  Chevron Indonesia Company, PT Indocemen Cirebon dan PT Pertamina Limau, PT OCI Melamin Kaltim, PT total E&P Kaltim, PT Kodeko Pertamina, Indocemen  Kalsel  dan  PT  Pupuk  Kujang,  PT Petrokimia Gresik,  CNOOC SES  Ltd, ,PT Chevron Geothermal Drajat, PT MAK Kalasan dan  PT Pertamina Prabumulih, PT Kaltim Industrial Estate, PT Star Energy Bandung , PT Pertamina (Kedeco) Gresik, PT Telkom Bandung, PT Margaria Group Yogya, PT Nusa Halmahera Mineral, PT Tambang Bukit Asam, PT Star Energy Bandung, Politeknik Aceh, PT KPI Kaltim, PT Medco Palembang, PT Pertamina Cirebon ,PT Timah Bangka, PT PJB Bali, Refinery Cilegon, PT Chevron Duri dan Drajat , PT PKT Kaltim,PT INALUM Medan, PT Petrokimia Gresik, PT PJB PLN Gresik, PT Chevron Drajat, PT Pertamina Jawa Timur ,PT Semen gresik &   PT YTL Jatim, PT  Sari Husada Yogyakarta,  PT Pupuk Kujang, Iros PTD Irak,PT Petrochina Jambi, PT PJB Gresik, PT Kaltim Prima Coal, PT Semen Hocim Cilacap, PT Badak LNG Kaltim , PT. YTL Paiton Jawatimur,PT  Star  Energy Bandung, Medco Sumatra, PT Sriboga Semarang,PT PLN UJB Cirata, PT Indonesia Power Semarang, PT Indonesia Power Grati, PT Indonesia Power Semarang, PT DSM Kaltim, PT. Pertamina Learning Center, PT. PUSRI Palembang, PT. VICO Indonesia Kaltim, PT Kaltim Pasific Amoniak , UDIKLAT/PUSDIKLAT PLN (Medan, Palembang, Jakarta, Semarang, Surabaya, Makasar),  PT  Chevron  salak  dan  PT   Indonesia   Power semarang,   PT. IPMOMI Paiton, PT Chevron Garut, PTP,  PT PetroChina Sorong, , PT PERTAMINA Aceh, PT Pertamina Cilacap,  PT PERTAMINA Dumai, PT AZET Surya Lestari, PT Panca Manunggal Semarang, PG Jatiroto Lumajang Jatim and others.

 

 

Bagikan:

KONTAK CEPAT

Tags

Avatar photo

 

Jika ada kebutuhan Inhouse training atau kelas khusus silahkan hubungi 0851-0197-2488 / 0899-8121-246 Petrus Soeganda. Untuk mengundang Petrus Soeganda sebagai Pembicara Internet Marketing

Programmable Logic Controller (PLC) : Advanced And Applicated

 

Programmable Logic Controller (PLC) : Advanced And Applicated

Tanggal
3 – 6 Juni 2014
30 Juni – 3 Juli 2014
12 – 15 Agustus 2014
2 – 5 September 2014
30 September – 3 Oktober 2014
4 – 7 November 2014
2 – 5 Desember 2014

Pukul
09.00-16.00 WIB

Tempat
Yogyakarta (Jogjakarta plaza hotel/Ibis hotel yogyakarta/Ibis Styles yogyakarta hotel/Mutiara hotel/ Melia Purosani hotel)

Investasi

  • Rp 8.500.000/person (full fare)  or
  • Rp 8.250.000/person (early bird, payment 1 week before training)  or
  • Rp 7.950.000/person (if there are 3 or more participants from the same company)

Fasilitas yang didapat

  • Modul Training
  • Flashdisk Training berisi materi training
  • Sertifikat
  • ATK: NoteBook dan Ballpoint
  • T-Shirt
  • Ransel
  • Foto Training
  • Ruang Training dengan fasilitas Full AC dan multimedia
  • Makan siang dan 2 kali coffeebreak
  • Instruktur yang Qualified
  • Transportasi untuk peserta dari hotel penginapan ke hotel tempat training – PP (jika peserta minimal dari satu perusahaan ada 4 peserta)

Instruktur
Tugino,ST.,MT. was graduated from electrical engineering Universitas Gadjah Mada,UGM Yogyakarta. He is lecturer at electrical engineering STTNAS Yogyakarta, for some subjects such as robotics, control engineering, Programmable Logic Controller(PLC), computer network, instrumentation and measurement, electric installation. And also as lecturer at mechanical engineering UJB Yogyakarta for subject electrical power engineering. Mr. Tugino,ST.,MT. is active training instructor, he has been delivering industrial training class to many companies in Indonesia for some subjects such as: Electrical Safety, DCS Operation and Maintenance, Genset Operation and Maintenance, Logic Control for Industry, Fundamental of Electrical, Advanced Process Control, PLC SIEMEN S7, Basic Telecommunication PABX, Audit Energi Listrik, Electrical Instalation in Hazardus Area, Low and Medium Voltage Switchgear, Cable Fault Location for Testing of Underground Power Cable, Protection of Electrical Power System, Building Maintenance Management, Generator and Excitation Operation and Maintenance, Lighning Protection and Grounding System, Basic Instrumentation and Control, Power Distribution System Protection, PLC Programmable Logic Controller using Siemen, Electrical & Mechanical Safety, Work at Height Scaffolding Safety, SCADA (Supervisory Control and Data Accuisition), Motor Maintenance and control, Control Valve and Instrumentation, And many others. Many companies has been becoming as participants in his training class such as: Chevron Indonesia Company, PT Indocemen Cirebon dan PT Pertamina Limau, PT OCI Melamin Kaltim, PT total E&P Kaltim, PT Kodeko Pertamina, Indocemen Kalsel dan PT Pupuk Kujang, PT Petrokimia Gresik, CNOOC SES Ltd, ,PT Chevron Geothermal Drajat, PT MAK Kalasan dan PT Pertamina Prabumulih, PT Kaltim Industrial Estate, PT Star Energy Bandung , PT Pertamina (Kedeco) Gresik, PT Telkom Bandung, PT Margaria Group Yogya, PT Nusa Halmahera Mineral, PT Tambang Bukit Asam, PT Star Energy Bandung, Politeknik Aceh, PT KPI Kaltim, PT Medco Palembang, PT Pertamina Cirebon ,PT Timah Bangka, PT PJB Bali, Refinery Cilegon, PT Chevron Duri dan Drajat , PT PKT Kaltim,PT INALUM Medan, PT Petrokimia Gresik, PT PJB PLN Gresik, PT Chevron Drajat, PT Pertamina Jawa Timur ,PT Semen gresik & PT YTL Jatim, PT Sari Husada Yogyakarta, PT Pupuk Kujang, Iros PTD Irak,PT Petrochina Jambi, PT PJB Gresik, PT Kaltim Prima Coal, PT Semen Hocim Cilacap, PT Badak LNG Kaltim , PT. YTL Paiton Jawatimur,PT Star Energy Bandung, Medco Sumatra, PT Sriboga Semarang,PT PLN UJB Cirata, PT Indonesia Power Semarang, PT Indonesia Power Grati, PT Indonesia Power Semarang, PT DSM Kaltim, PT. Pertamina Learning Center, PT. PUSRI Palembang, PT. VICO Indonesia Kaltim, PT Kaltim Pasific Amoniak , UDIKLAT/PUSDIKLAT PLN (Medan, Palembang, Jakarta, Semarang, Surabaya, Makasar), PT Chevron salak dan PT Indonesia Power semarang, PT. IPMOMI Paiton, PT Chevron Garut, PTP, PT PetroChina Sorong, , PT PERTAMINA Aceh, PT Pertamina Cilacap, PT PERTAMINA Dumai, PT AZET Surya Lestari, PT Panca Manunggal Semarang, PG Jatiroto Lumajang Jatim and others.

Tujuan Pelatihan
Kursus ini memberikan pemahaman lebih kompleks terhadap PLC, peserta akan mendapatkan pengetahuan mengenai variasi perintah pemrograman dan juga penulisan pemrograman yang digunakan didalam : I/O devices, BCD thumbwell switches, stepper motors, optical rotary encoder, dll. Kursus ini 75 % merupakan praktek.

Cakupan Materi Training

  1. Basics refresher (Logic and software).
  2. Advanced bit level instructions (One Shot Rising, Latch, Unlatch, Status bits, etc).
  3. Digital number / match operations (Binary, Octal, Hexadecimal, BCD).
  4. BCD I/O devices.
  5. Data handling instructions (Shift registers, Sequencers, FIFO, LIFO)
  6. Program flow instructions (Subroutines, Jumps, MCR’s)
  7. World level logic operations.
  8. Immediate I/O.
  9. High speed counters.
  10. Analog Inputs.
  11. Analog Outputs.
  12. Practice and interactive discussion

Wajib diikuti oleh

  1. D3 Elektro atau SLTA yang berpengalaman kerja minimal 3 tahun, dan atau setara.
  2. Teknisi, Operator dan Supervisor yang memiliki basic computer skills dan familiar dengan basic electrical concept.
  3. Mereka yang dalam tugasnya berhubungan dan atau terkait dengan materi kursus.
  4. Semua pihak yang ingin memahami topik ini

Bagikan:

KONTAK CEPAT

Tags

Avatar photo

 

Jika ada kebutuhan Inhouse training atau kelas khusus silahkan hubungi 0851-0197-2488 / 0899-8121-246 Petrus Soeganda. Untuk mengundang Petrus Soeganda sebagai Pembicara Internet Marketing

Basic Refrigeration (YOGYAKARTA)

 

Basic Refrigeration (YOGYAKARTA)

Tanggal
26 – 29 Mei 2014
24 – 27 Juni 2014
15 – 18 Juli 2014
26 – 29 Agustus 2014
23 – 26 September 2014
28 – 31 Oktober 2014
25 – 28 November 2014
16 – 19 Desember 2014

Tempat
Yogyakarta (Jogjakarta plaza hotel/Ibis hotel yogyakarta/Ibis Styles yogyakarta hotel/Mutiara hotel/ Melia Purosani hotel)

TRAINING DURATION :   4 hari

OBJECTIVES :
Memberikan pengetahuan tentang dasar sistem pendinginan (refrigerasi) antara lain : dasar-dasar thermodinamika, siklus refrigerant, peralatan refrigerasi (kompressor, evaporator, condenser, expansion valve), perpipaan refrigerant, operation and maintenance.

CAKUPAN MATERI TRAINING:
•    Basic Concept engineering thermodynamics.
•    Refrigerant
•    Siklus refrigerant
•    Load estimating : cooling and heating
•    Peralatan refrigerasi,
o    kompresor,
o    evaporator
o    condenser
o    expansion valve
•    Refrigerant piping
•    Heat pump
•    Operation and maintenance of refrigeration

WHO SHOULD ATTEND THIS TRAINING? :
Peserta yang diharapkan berpartisipasi dalam program ini antara lain Teknisi, Engineer, Supervisor yang bekerja pada bidang maintenance di perusahaan.

INVESTATION PRICE/PERSON :   

  • Rp 7.950.000/person (full fare)  or
  • Rp 7.750.000/person (early bird, payment 1 week before training)  or
  • Rp 7.500.000/person (if there are 3 or more participants from the same company)

FACILITIES FOR PARTICIPANTS:

  • Modul Training
  • Flashdisk Training berisi materi training
  • Sertifikat
  • ATK: NoteBook dan Ballpoint
  • T-Shirt
  • Ransel
  • Foto Training
  • Ruang Training dengan fasilitas Full AC dan multimedia
  • Makan siang dan 2 kali coffeebreak
  • Instruktur yang Qualified
  • Transportasi untuk peserta dari hotel penginapan ke hotel tempat training – PP (jika peserta minimal dari satu perusahaan ada 4 peserta)

TRAINING INSTRUCTOR
Ir. Y. Agus Jayatun, MT.,IPP. Adalah lulusan dari teknik mesin UGM, dan sekarang Beliau menjadi dosen di Teknik Mesin Sekolah Tinggi Teknologi Nasional Yogyakarta. Pak Agus Jayatun sudah sering menjadi instruktur untuk training-training di bidang kompetensi Beliau, seperti: Centrifugal Pump; Operation and Maintenance, Compressor; Operation and Maintenance, Boiler; Operator Sertification, Maintenance Management, Total Alignment and Balancing, Mechanical Power Transmision, Pipeline design, construction and maintenance, Control Valve, design, operation and maintenance, Rotating Equipment; Operation and Maintenance, Bearing; Design and Maintenance, Lubrication, Vibration analysis and diagnostic, Above Ground Storage Tank, Corrosion Control : Sacrifice Anode, Impressed Current, Galvanizing, Metallurgy for non metallurgic engineers, Metallurgy in Welding, Health, Safety and Environment (HSE). Pak Agus Jayatun juga sudah berpengalaman bekerja di beberapa perusahaan dengan berbagai posisi seperti dari sales engineer, Mechanical and Electrical Site Engineer, M/E. Site Engineer pada Process of Clean Water Instalation, M/E. Site Engineer pada Office Building of PLN, Supervisor M/E Engineer, Mechanical Engineer pada Detail Engineering Design of Non Liquid Waste of Komplek Industri Kulit dan masih banyak yang lainnya. Beliau memiliki beberapa sertifikasi profesional dari PII dalam bidang Plumbing/Piping, Air Conditioning, Indoor Building Transportation, Mechanical, dan electrical.

Bagikan:

KONTAK CEPAT

Tags

Avatar photo

 

Jika ada kebutuhan Inhouse training atau kelas khusus silahkan hubungi 0851-0197-2488 / 0899-8121-246 Petrus Soeganda. Untuk mengundang Petrus Soeganda sebagai Pembicara Internet Marketing

Basic Mechanical (YOGYAKARTA)

 

Basic Mechanical (YOGYAKARTA)

Tanggal
9 – 12 Juni 2014
1 – 4 Juli 2014
12 – 15 Agustus 2014
8 – 11 September 2014
6 – 9 Oktober 2014
4 – 7 November 2014
2 – 5 Desember 2014

Pukul
09.00-16.00 WIB

Tempat
Yogyakarta (Jogjakarta plaza hotel/Ibis hotel yogyakarta/Ibis Styles yogyakarta hotel/Mutiara hotel/ Melia Purosani hotel)

PENDAHULUAN :
Ilmu Teknik bidang Teknik Mesin ( Mechanical Engineering ) merupakan salah satu pendukung utama berkembangnya industri, sehingga penguasaan yang memadai di bidang Mechanical Engineering merupakan syarat mutlak untuk dapat menangani peralatan-peralatan industri baik bagi seorang Engineer, Technician atupun Operator. Mechanical Engineering merupakan cabang ilmu teknik yang berpijak terutama antara lain pada ilmu-ilmu Matematika, Kinematika Dinamika, Material, Mekanika Material, Mekanika Fluida, Mekanika Panas,Thermodinamika dan Teknik Pengukuran serta Teknik Pengendalian. Kursus singkat ini mendiskusikan dasar-dasar ilmu di atas termasuk penerapannya di bidang Mechanical Engineering. Selesai mengikuti kursus ini peserta diharapkan lebih memahami dasar-dasar ilmu Mechanical sehingga semakin memahami cara menangani peralatan industri baik dari segi desain konstruksi, pengoperasian dan pemeliharaan. Kursus ini dapat diikuti oleh profesional di bidang engineering dari berbagai macam latar belakang keilmuan yang telah menempuh derajat pendidikan S1 fresh graduate, D3 dengan pengalaman kerja minimal 2 tahun dan STM/SMA dengan pengalaman kerja minimal 5 tahun.

CAKUPAN MATERI TRAINING :

  1. Ilmu Material Dasar (Ferrous dan non Ferrous dan treatment)
  2. Dasar-dasar Mekanika Material
  3. Dasar-dasar Kinematika Dinamika dan penerapannya
  4. Dasar-dasar Mekanika Fluida dan penerapannya
  5. Dasar-dasar Thermodinamika dan penerapannya
  6. Perpindahan Panas Dasar
  7. Dasar-dasar Teknik Pengukuran dan Pengendalian

TRAINING DURATION : 5 hari

INVESTATION PRICE/PERSON :

  • Rp 7.950.000/person (full fare)  or
  • Rp 7.750.000/person (early bird, payment 1 week before training)  or
  • Rp 7.500.000/person (if there are 3 or more participants from the same company)

FACILITIES FOR PARTICIPANTS:

  1. Modul Training
  2. Flashdisk Training berisi materi training
  3. Sertifikat
  4. ATK: NoteBook dan Ballpoint
  5. T-Shirt
  6. Ransel
  7. Foto Training
  8. Ruang Training dengan fasilitas Full AC dan multimedia
  9. Makan siang dan 2 kali coffeebreak
  10. Instruktur yang Qualified
  11. Transportasi untuk peserta dari hotel penginapan ke hotel tempat training – PP (jika peserta minimal dari satu perusahaan ada 4 peserta)

TRAINING INSTRUCTOR
Ir. Y. Agus Jayatun, MT.,IPP. Adalah lulusan dari teknik mesin UGM, dan sekarang Beliau menjadi dosen di Teknik Mesin Sekolah Tinggi Teknologi Nasional Yogyakarta. Pak Agus Jayatun sudah sering menjadi instruktur untuk training-training di bidang kompetensi Beliau, seperti: Centrifugal Pump; Operation and Maintenance, Compressor; Operation and Maintenance, Boiler; Operator Sertification, Maintenance Management, Total Alignment and Balancing, Mechanical Power Transmision, Pipeline design, construction and maintenance, Control Valve, design, operation and maintenance, Rotating Equipment; Operation and Maintenance, Bearing; Design and Maintenance, Lubrication, Vibration analysis and diagnostic, Above Ground Storage Tank, Corrosion Control : Sacrifice Anode, Impressed Current, Galvanizing, Metallurgy for non metallurgic engineers, Metallurgy in Welding, Health, Safety and Environment (HSE). Pak Agus Jayatun juga sudah berpengalaman bekerja di beberapa perusahaan dengan berbagai posisi seperti dari sales engineer, Mechanical and Electrical Site Engineer, M/E. Site Engineer pada Process of Clean Water Instalation, M/E. Site Engineer pada Office Building of PLN, Supervisor M/E Engineer, Mechanical Engineer pada Detail Engineering Design of Non Liquid Waste of Komplek Industri Kulit dan masih banyak yang lainnya. Beliau memiliki beberapa sertifikasi profesional dari PII dalam bidang Plumbing/Piping, Air Conditioning, Indoor Building Transportation, Mechanical, dan electrical.

 

Bagikan:

KONTAK CEPAT

Tags

Avatar photo

 

Jika ada kebutuhan Inhouse training atau kelas khusus silahkan hubungi 0851-0197-2488 / 0899-8121-246 Petrus Soeganda. Untuk mengundang Petrus Soeganda sebagai Pembicara Internet Marketing

Vibration Analysis (YOGYAKARTA)

 

Vibration Analysis (YOGYAKARTA)

Tanggal
26 – 28 Mei 2014
24 – 26 Juni 2014
16 – 18 Juli 2014
27 – 29 Agustus 2014
23 – 25 September 2014
27 – 29 Oktober 2014
25 – 27 November 2014
29 – 31 Desember 2014

Tempat
Yogyakarta (Jogjakarta plaza hotel/Ibis hotel yogyakarta/Ibis Styles yogyakarta hotel/Mutiara hotel/ Melia Purosani hotel)

TRAINING OBJECTIVES :

  • Introduce machinery condition – base maintenance concept by vibration monitoring and analysis.
  • Better knowledge and skill to monitoring machinery failure by vibration analysis, e.g., bearing problem, unbalance, alignment, gearbox, looseness, blade and vane, electric motor etc.

TRAINING MATERIAL OUTLINE :

  1. Fundamental of vibration: time domain, frequency domain, FFT Spectrum.
  2. Vibration Instrumentation: accelerometer, velocity, proximity pick up, digital signal analyzer.
  3. Vibration measurement technique
  4. Data analysis
  5. Fault diagnosis: rotor, fan unbalance, misalignment problem, roller and journal/ sleeve bearing problem, mechanical looseness, gear box, belt problem, electric motor, vane and blade, resonance/ natural frequency.
  6. Vibration standard and machinery vibration evaluation criteria
  7. Vibration damping/ absorber
  8. Case study and interactive discussion

TRAINING DURATION : 3 hari

INVESTATION PRICE/PERSON :

  • Rp 5.950.000/peserta (bayar penuh)  atau
  • Rp 5.750.000/peserta (early bird, yang membayar 1 minggu sebelum training) atau
  • Rp 5.500.000/peserta (grup, untuk 3 peserta atau lebih dari 1 perusahaan yang sama)

FACILITIES FOR PARTICIPANTS:

  • Modul Training
  • Flashdisk Training berisi materi training
  • Sertifikat
  • ATK: NoteBook dan Ballpoint
  • T-Shirt
  • Ransel
  • Foto Training
  • Ruang Training dengan fasilitas Full AC dan multimedia
  • Makan siang dan 2 kali coffeebreak
  • Instruktur yang Qualified
  • Transportasi untuk peserta dari hotel penginapan ke hotel tempat training – PP (jika peserta minimal dari satu perusahaan ada 4 peserta)

TRAINING INSTRUCTOR
Ir. Y. Agus Jayatun, MT.,IPP. Adalah lulusan dari teknik mesin UGM, dan sekarang Beliau menjadi dosen di Teknik Mesin Sekolah Tinggi Teknologi Nasional Yogyakarta. Pak Agus Jayatun sudah sering menjadi instruktur untuk training-training di bidang kompetensi Beliau, seperti: Centrifugal Pump; Operation and Maintenance, Compressor; Operation and Maintenance, Boiler; Operator Sertification, Maintenance Management, Total Alignment and Balancing, Mechanical Power Transmision, Pipeline design, construction and maintenance, Control Valve, design, operation and maintenance, Rotating Equipment; Operation and Maintenance, Bearing; Design and Maintenance, Lubrication, Vibration analysis and diagnostic, Above Ground Storage Tank, Corrosion Control : Sacrifice Anode, Impressed Current, Galvanizing, Metallurgy for non metallurgic engineers, Metallurgy in Welding, Health, Safety and Environment (HSE). Pak Agus Jayatun juga sudah berpengalaman bekerja di beberapa perusahaan dengan berbagai posisi seperti dari sales engineer, Mechanical and Electrical Site Engineer, M/E. Site Engineer pada Process of Clean Water Instalation, M/E. Site Engineer pada Office Building of PLN, Supervisor M/E Engineer, Mechanical Engineer pada Detail Engineering Design of Non Liquid Waste of Komplek Industri Kulit dan masih banyak yang lainnya. Beliau memiliki beberapa sertifikasi profesional dari PII dalam bidang Plumbing/Piping, Air Conditioning, Indoor Building Transportation, Mechanical, dan electrical.

 

Bagikan:

KONTAK CEPAT

Tags

Avatar photo

 

Jika ada kebutuhan Inhouse training atau kelas khusus silahkan hubungi 0851-0197-2488 / 0899-8121-246 Petrus Soeganda. Untuk mengundang Petrus Soeganda sebagai Pembicara Internet Marketing

Chat dengan kami
CV INFO SEMINAR
0899-8121-246

2024

informasi-seminar.com | infoseminar.co.id